View AS1364-BTDT-12_4522918.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Datasheet
AS1364
1 A , L o w - D r o p o u t L i n e a r Vo l ta g e R e g u l a t o r
1 General Description
The AS1364 is a low-dropout linear regulator (LDO) designed to operate from 2V to 5.5V input, that delivers a wide range of highly accurate (0.75%) factorytrimmed output voltages as well as adjustable output voltages (using an external resistor-divider network). The ultra-low dropout device requires only 140mV dropout voltage while delivering a guaranteed 1A load current and is therefore perfectly suited for battery-operated portable applications. Additionally the AS1364 offers extremly low 10VRMS (100Hz to 100kHz) or 45VRMS (10Hz to 1MHz) output voltage noise. Table 1. Standard Products Model AS1364-AD AS1364-_ _ Output Type Adjustable Fixed BYP No Yes SET Yes No
2 Key Features
! ! ! ! ! ! ! ! ! ! ! !
Guaranteed Output Current: 1A Low Dropout: 140mV @ 1A Output Voltage Accuracy: Up to 0.75% 2.0V to 5.5V Input Voltage Fixed VOUT: 1.2V to 5.0V Adjustable VOUT: 1.2V to 5.3V Low Ground Current: 35A Low Shutdown Current: 10nA Low Output Noise: 45VRMS (from 10Hz to 1MHz) Thermal Overload Protection Output Current Limit 8-pin TDFN 3x3mm Package
The device features an internal PMOS pass transistor (for a low supply current of only 35A), reset output, a low-power shutdown mode, and protection from shortcircuit and thermal-overload conditions. The AS1364 is available in an 8-pin TDFN 3x3mm package.
3 Applications
The device is ideal for laptops, PDAs, portable audio devices, mobile phones, cordless phones, and any other battery-operated portable device.
Figure 1. AS1364 - Typical Application Diagram
3 VIN CIN 4.7F On Off IN 4 IN 2 EN 8 GND
6 OUT 5 COUT 4.7F VOUT
AS1364
OUT 1 POK 7 SET/BYP Reset Output CBYP 10nF
www.austriamicrosystems.com
Revision 1.05
1 - 15
AS1364
Datasheet - P i n o u t
4 Pinout
Pin Assignments
Figure 2. Pin Assignments (Top View)
POK 1 EN 2
8 GND 7 SET/BYP
AS1364
IN 3 IN 4 6 OUT 5 OUT
Pin Descriptions
Table 2. Pin Descriptions Pin Number 1 Pin Name POK Description Note: Open-Drain POK Output. POK remains low while VOUT is below the POK threshold. Connect a 100k pull-up resistor from this pin to OUT to obtain an output voltage (see Figure 1 on page 1). Active-Low Shutdown Input. A logic low disables the output and reduces the supply current to 0.1A. In shutdown, the POK output is low and OUT high impedance. VDD: Normal operation. GND: Shutdown. 2.0V to 5.5V Supply Voltage. Bypass with a 4.7F input capacitor to GND (see Capacitor Selection and Regulator Stability on page 12). These inputs are internally connected, but they also must be externally connected for proper operation. Regulator Output. Bypass with a 4.7F low-ESR output capacitor to GND. Connect the OUT pins together externally. Voltage-Setting Input. Connect to GND to select the factory-preset output voltage. Connect this pin to an external resistor-divider for adjustable-output operation (see Figure 1 on page 1). (AS1364-AD only) Bypass Pin. Connect a 10nF capacitor from this pin to OUT to improve PSRR and noise performance. (AS1364-AD does not offer this feature) Ground
2
EN
3, 4 5, 6
IN OUT
7
SET/BYP
8
GND
www.austriamicrosystems.com
Revision 1.05
2 - 15
AS1364
Datasheet - A b s o l u t e M a x i m u m R a t i n g s
5 Absolute Maximum Ratings
Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3. Absolute Maximum Ratings Parameter IN, EN, POK to GND OUT, SET/BYP to GND Output Short-Circuit Duration Thermal Resistance JA ESD Latch-Up Operating Temperature Range Storage Temperature Range Junction Temperature -100 -40 -65 2 +100 +85 +150 +150 Min -0.3 -0.3 Max +7 VIN + 0.3 Infinite 36.3 C/W kV mA C C C The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/JEDEC J-STD-020D "Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices". The lead finish for Pb-free leaded packages is matte tin (100% Sn). on PCB HBM MIL-Std. 883E 3015.7 methods JEDEC 78 Units V V Comments
Package Body Temperature
+260
C
www.austriamicrosystems.com
Revision 1.05
3 - 15
AS1364
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6 Electrical Characteristics
VIN = VOUT(NOM) + 500mV or VIN = +2.0V (whichever is greater),CIN = COUT = 4.7F, EN = IN, TAMB = -40C to +85C (unless otherwise specified). Typical values are at TAMB = +25C. Table 4. Electrical Characteristics Symbol VIN VPOR Parameter Input Voltage Power On Reset Output Voltage Accuracy (Preset Mode) Adjustable Output Voltage Range SET/BYP Voltage Threshold (Adjustable Mode) Guaranteed Output Current (RMS) Short-Circuit Current Limit In-Regulation Current Limit SET/BYP Threshold ISET IQ VIN VOUT VLNR VLDR SET/BYP Input Bias Current Ground-Pin Current
2
Condition
Min 2.0
Typ
Max 5.5
Unit V V
Falling, 100mV hysteresis IOUT = 250mA, TAMB = +25C IOUT = 250mA IOUT = 1mA to 1A, VIN > (VOUT + 0.5V)
1
1.79 -0.75 -1.5 -2 1.2
1.87
1.95 +0.75 +1.5 +2 5.3
%
VOUT VSET/BYP IOUT ILIMIT
V V A
VIN = 2.5V, IOUT = 250mA, VOUT set to 2.0V
1.17 1
1.20
1.23
VOUT = 0 VOUT > 96% of nominal value, VIN 2.0V
1.1
1.5 1.5
2.3
A A
50 VSET/BYP = 1.20V IOUT = 100A IOUT = 1A IOUT = 250mA, VOUT = 3.3V IOUT = 1A, VOUT = 3.3V VIN from (VOUT + 100mV) to 5.5V, ILOAD = 5mA IOUT = 1mA to 1A f = 1kHz, IOUT = 10mA, CBYP = 10nF f = 1kHz, IOUT = 10mA -0.125 -100
100
150 +100
mV nA A
35 75 35 140
150 200 85 320 +0.125 0.001
Dropout Voltage Line Regulation
mV %/V %/mA
Load Regulation
78 72 75 65 54 46 10 50 45 70 VRMS dB
PSRR
Ripple Rejection
f = 10kHz, IOUT = 10mA, CBYP = 10nF f = 10kHz, IOUT = 10mA f = 100kHz, IOUT = 10mA, CBYP = 10nF f = 100kHz, IOUT = 10mA 100Hz to 100kHz, COUT = 3.3F, CBYP = 10nF;
Output Voltage Noise
100Hz to 100kHz, COUT = 3.3F; 10Hz to 1MHz, COUT = 3.3F, CBYP = 10nF; 10Hz to 1MHz, COUT = 3.3F;
www.austriamicrosystems.com
Revision 1.05
4 - 15
AS1364
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
Table 4. Electrical Characteristics (Continued) Symbol Shutdown IOFF VIH VIL ISHDNN POK Output VOL POK Output Low Voltage Operating Voltage Range for Valid POK Signal POK Output High leakage Current POK Threshold Thermal Protection TSHDNN Thermal Shutdown Temperature 170 20 C C POK sinking 1mA POK sinking 100A POK = 5.5V, TAMB = +25C TAMB = +85C Rising edge (referenced to VOUT(NOM)) 90 1.1 1 5 94 98 0.05 0.25 5.5 V V nA % EN Input Threshold Shutdown Supply Current EN = GND, VIN = 5.5V, TAMB = 25C EN = GND, VIN = 5.5V 2.0V < VIN < 5.5V 2.0V < VIN < 5.5V EN = IN or GND, TAMB = +25C TAMB = +85C 1 5 1.6 0.6 0.01 0.1 0.5 15 A V V nA Parameter Condition Min Typ Max Unit
EN Input Bias Current
TSHDNN Thermal Shutdown Hysteresis
1. Guaranteed by production test of load regulation and line regulation. 2. Dropout voltage is defined as VIN - VOUT, when VOUT is 100mV below the value of VOUT measured for VIN = (VOUT(NOM) + 500mV). Since the minimum input voltage is 2.0V, this specification is only valid when VOUT(NOM) > 2.0V.
Note: All limits are guaranteed. The parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality Control) methods.
www.austriamicrosystems.com
Revision 1.05
5 - 15
AS1364
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
7 Typical Operating Characteristics
VIN = VOUT(NOM) + 0.5V, CIN = COUT = 4.7F, TAMB = 25C (unless otherwise specified). Figure 3. VDROP vs. IOUT;
160 140
Figure 4. VOUT vs. IOUT; VOUT(NOM) = 3.3V
3.31 3.309
.
Dropout Voltage (mV)
120 100 80 60 40 20 0 0 200 400 600 800 1000
Output Voltage (V) .
3.308 3.307 3.306 3.305 3.304 3.303 3.302 3.301 3.3 0 200 400 600 800 1000
Load Current (mA) Figure 5. VOUT vs. Temperature; VOUT(NOM) = 3.3V
3.32 3.315
Output Current (mA) Figure 6. VOUT vs. VIN; VOUT(NOM) = 3.3V
3.5 3
Output Voltage (V) .
3.31 3.305 3.3 3.295 3.29 3.285 -45 -30 -15
Output Voltage (V) .
2.5 2 1.5 1 0.5 0
no load Iout = 1A
0
15
30
45
60
75
90
0
1
2
3
4
5
6
Temperature (C) Figure 7. Quiescent Current vs. VIN;
180
no load
Input Voltage (V) Figure 8. Quiescent Current vs. IOUT;
90
Iout = 1A
160
80
.
Quiescent Current (A)
120 100 80 60 40 20 0 0 1 2 3 4 5 6
Quiescent Current (A)
140
.
70 60 50 40 30 20 10 0 0 200 400 600 800 1000
Vin = 3.8V Vin = 5.5V
Input Voltage (V) www.austriamicrosystems.com Revision 1.05
Output Current (mA) 6 - 15
AS1364
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 9. Quiescent Current vs. Temperature;
90 80
Figure 10. Spectral Noise vs. Freq.; IOUT = 10mA,
10
COUT = 3.3F
Quiescent Current (A)
70 60 50 40 30 20 10 0 -45 -30 -15
no load Iout = 250mA
Output Noise Density (V/ Hz)
90
.
.
1 0.1 0 15 30 45 60 75 0.01 0.01
0.1
1
10
100
1000
Temperature (C)
Frequency (kHz)
Figure 11. PSRR vs. Frequency; IOUT = 10mA
100
80
PSRR (dB) .
60
40
20
0 0.01
1
100
10000
Frequency (kHz)
www.austriamicrosystems.com
Revision 1.05
7 - 15
AS1364
Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s
Figure 12. Line Transient Response; VIN = 3.8V to 4.3V, IOUT = 100mA
Figure 13. Load Transient Response; VIN = 3.8V, IOUT = 50mA to 500mA
200mV/Div
VIN
20mV/Div
VOUT
100s/Div
5s/Div
Figure 14. Startup; VIN = 3.8V, IOUT = 100mA
Figure 15. Startup; VIN = 3.8V, IOUT = 100mA
1V/Div
1V/Div
1ms/Div
20s/Div
www.austriamicrosystems.com
Revision 1.05
1V/Div
VOUT
VOUT
1V/Div
VIN
VIN
200mA/Div
IOUT
50mV/Div
VOUT
8 - 15
AS1364
Datasheet - D e t a i l e d D e s c r i p t i o n
8 Detailed Description
The AS1364 output voltage is factory-trimmed or is adjustable from +1.2 to +5V, and is guaranteed to supply 1A of output current. The device consists of a +1.20V internal reference, error amplifier, MOSFET driver, P-channel pass transistor, internal feedback voltage-divider and a comparator (see Figure 16).
Figure 16. AS1364 - Block Diagram
VIN 2.0V to 5.5V CIN 4.7F
4 IN 3 IN MOSFET Driver w/ILIM Thermal Sensor 5 OUT 6 VOUT 1.2V to 5.0V COUT 4.7F + RPOK 100k Error Amplifier 1 POK + - + - + - 100mV + - 8 GND - 1.20V Reference R1
On Off VOUT Logic Supply Voltage
2 EN
Shutdown Logic
OUT
To Controller
7 SET/BYP R2
AS1364
94%VREF
The +1.20V reference is connected to the inverting input of the error amplifier, which compares this reference with the selected feedback voltage and amplifies the difference. The MOSFET driver reads the error signal and applies the appropriate drive to the P-channel transistor. If the feedback voltage is lower than the reference, the pass transistor gate is pulled lower, allowing more current to pass increasing the output voltage. If the feedback voltage is too high, the pass transistor gate is pulled up, allowing less current to pass to the output. The low VOUT comparator senses when the feedback voltage has dropped 6% below its expected level, causing POK to go low. The output voltage is fed back through either an internal resistor-divider connected to OUT or an external resistor network connected to SET. The comparator examines VSET/BYP and selects the feedback path. If VSET/BYP is below 50mV, the internal feedback path is used and the output is regulated to the factory-preset voltage.
www.austriamicrosystems.com
Revision 1.05
9 - 15
AS1364
Datasheet - D e t a i l e d D e s c r i p t i o n
Output Voltage Selection
At the factory trimmed versions of the AS1364 offering the bypass pin (see Figure 1 on page 1), the output voltage is then set to an internally trimmed voltage (see Ordering Information on page 14). For the adjustable AS1364-AD, an output voltage between +1.2V and +5V can be set by using two external resistors (see Figure 17). In this mode, VOUT is determined by: R1 V OUT = V SETBYP x 1 + ----- R 2 Where: VSET/BYP = +1.20V. A simplification of R1 and R2 selection is: V OUT R 1 = R 2 x -------------------- - 1 V SETBYP (EQ 2)
(EQ 1)
Since the input bias current at SET is less than 100nA, large resistance values can be used for R1 and R2 to minimize power consumption and therefore increasing efficiency. Note: Up to 125k is acceptable for R2. If the SET pin is connected to GND without a resistor, 3.3V will be set as output voltage. In preset voltage mode, the impedance from SET to GND should be less than 10k or spurious conditions may cause the voltage at SET to exceed the 50mV threshold.
Figure 17. Adjustable Output Voltage Typical Application
3 VIN CIN 4.7F On Off IN 4 IN 2 EN 8 GND 5 OUT 6 COUT 4.7F VOUT R1
AS1364
OUT 7 SET/BYP 1 POK Reset Output
R2
Shutdown
If pin EN is connected to GND the AS1364 is disabled. In shutdown mode all internal circuits are turned off, reducing supply current to 10nA (typ). For normal device operation pin EN must be connected to IN. During shutdown, POK goes low.
Power-OK
The AS1364 features a power-ok indicator that asserts when the output voltage falls out of regulation. The open-drain POK output goes low when output voltage at OUT falls 6% below its nominal value. A 100k pull-up resistor from POK to a (typically OUT) provides a logic control signal. POK can be used as a power-on-reset (POR) signal to a microcontroller or can drive an external LED to indicate a power failure condition. Note: POK is low during shutdown.
www.austriamicrosystems.com
Revision 1.05
10 - 15
AS1364
Datasheet - D e t a i l e d D e s c r i p t i o n
Current Limiter
The AS1364 features current limiting circuitry that monitors the pass transistor, limiting short-circuit output current to 1.5A (typ). The circuitry of the AS1364 allows that the output can be shorted to ground for an indefinite period of time without damaging the device.
Internal P-Channel Pass Transistor
The AS1364 features a 1A P-channel MOSFET pass transistor and consumes only a maximum of 200A of quiescent current under heavy loads as well as in dropout.
Thermal Protection
Integrated thermal overload protection limits the total power dissipation in the AS1364. When the junction temperature (TJ) exceeds +170C typically, the pass transistor is turned off. Normal operation is continued when TJ drops approximately 20C. Note: Regardless of the hysteresis, continuous short-circuit condition will result in a pulsed output.
Operating Region and Power Dissipation
Maximum power dissipation of the AS1364 depends on the thermal resistance of the package and the PCB, the temperature difference between the die junction and ambient air, and the rate of air flow. The power dissipated in the device is given as:
PD = I OUT x ( V IN - V OUT )
(EQ 3)
The maximum power dissipation is calculated: T J ( MAX ) - T AMB PDMAX = -------------------------------------- JC + JA
(EQ 4)
Where: TJ(MAX) - TAMB is the temperature difference between the device die junction and the surrounding air. JC is the thermal resistance of the junction to the case. JA is the thermal resistance from the case through the PCB, copper traces, and other materials to the surrounding air. Connect the exposed thermal pad and GND to circuit ground by using a large pad, or multiple vias to the ground plane.
www.austriamicrosystems.com
Revision 1.05
11 - 15
AS1364
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
9 Application Information
Capacitor Selection and Regulator Stability
Input and output capacitors are required for stable operation of the AS1364 over the full temperature range and with load currents up to 1A. Connect CIN and COUT as close to the AS1364 as possible to minimize the impact of PC board trace inductance.
Input Capacitor
For CIN, a 4.7F capacitor between IN and ground is sufficient. CIN reduces the source impedance of the input supply and may be smaller than 4.7F if powered from regulated power supplies or low-impedance batteries. Larger input capacitor values and lower ESR provide better noise rejection and line-transient response.
Output Capacitor
A 4.7F low-ESR capacitor between OUT and ground is sufficient for COUT. The output capacitor's ESR affects stability and output noise. An output capacitors with an ESR of 0.5 or less is recommended to ensure stability and optimum transient response. Reduced output noise and improve load-transient response, stability, and power-supply rejection by using large output capacitors with low ESR.
Noise, PSRR, and Transient Response
AS1364 output noise is typically 10VRMS (100Hz to 100kHz) or 45VRMS (10Hz to 1MHz) during normal operation. This is suitably low for most applications (see Figure 10 on page 7). The AS1364 is designed to achieve extremly low dropout voltage and low quiescent current in battery-powered systems while still maintaining excellent noise performance, transient response, and PSRR. See the Figure 11 on page 7 for a plot of power-supply rejection ratio (PSRR) versus frequency. When operating from very noisy sources, the factory preset variants a recommanded since they offer improved noise performance over the adjustable variants.
www.austriamicrosystems.com
Revision 1.05
12 - 15
AS1364
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
10 Package Drawings and Markings
The device is available in an 8-pin TDFN 3x3mm package. Figure 18. 8-pin TDFN 3x3mm Package
D D2 SEE DE TAIL B B
E2/2
2x aaa C PIN 1 INDEX AREA (D/2 xE/2)
4 NX K
PIN 1 INDEX AREA (D/2 xE/2) 4 aaa C 2x TOP VIEW
7 e 6
N N -1 (ND -1) X e
BTM VIEW
NX b bbb ddd C
5 CAB
e e/2
Term inal Tip
5 ccc C
A3
E2
E
A
D atum A or B E VE N T E RMINAL S IDE
Symbol A A1 A3 L1 L2 aaa bbb ccc ddd eee ggg Notes:
Min 0.70 0.00
Typ 0.75 0.02 0.20 REF
Max 0.80 0.05 0.15 0.13
0.15 0.10 0.10 0.05 0.08 0.10
Notes 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2
Symbol D BSC E BSC D2 E2 L K b e N ND
Min
Typ 3.00 3.00
Max
A1
1. Figure 18 is shown for illustration only. 2. All dimensions are in millimeters; angles in degrees. 3. Dimensioning and tolerancing conform to ASME Y14.5 M-1994. 4. N is the total number of terminals. 5. The terminal #1 identifier and terminal numbering convention shall conform to JEDEC 95-1, SPP-012. Details of terminal #1 identifier are optional, but must be located within the zone indicated. The terminal #1 identifier may be either a mold or marked feature. 6. Dimension b applies to metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 7. ND refers to the maximum number of terminals on side D. 8. Unilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals
A
NX L
7 NX 0.08 C
D 2/2
C
SEATING PLANE
S IDE V IEW
1.60 1.35 0.30 0 0.20 0.25
0.40
2.50 1.75 0.50 14 0.35
0.30 0.65 8 4
Notes 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2, 5 1, 2 1, 2, 5
www.austriamicrosystems.com
Revision 1.05
13 - 15
AS1364
Datasheet - O r d e r i n g I n f o r m a t i o n
11 Ordering Information
The device is available as the standard products shown in Table 5. Table 5. Ordering Information Ordering Code AS1364-BTDT-AD AS1364-BTDT-12* AS1364-BTDT-15 AS1364-BTDT-18 AS1364-BTDT-30 AS1364-BTDT-33 AS1364-BTDT-45 *Future product. Non-standard devices are available between 1.4V and 4.6V in 50mV steps and between 4.6V and 5.0V in 100mV steps. For more information and inquiries contact http://www.austriamicrosystems.com/contact Marking ASRF ASRN ASRG ASRH ASRJ ASRI ASRK Output adjustable (preset to 3.3V) 1.2V 1.5V 1.8V 3.0V 3.3V 4.5V SET/BYP SET BYP BYP BYP BYP BYP BYP Delivery Form Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Package 8-pin TDFN 3x3mm 8-pin TDFN 3x3mm 8-pin TDFN 3x3mm 8-pin TDFN 3x3mm 8-pin TDFN 3x3mm 8-pin TDFN 3x3mm 8-pin TDFN 3x3mm
Note: All products are RoHS compliant and Pb-free. Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect For further information and requests, please contact us mailto:sales@austriamicrosystems.com or find your local distributor at http://www.austriamicrosystems.com/distributor
www.austriamicrosystems.com
Revision 1.05
14 - 15
AS1364
Datasheet
Copyrights
Copyright (c) 1997-2009, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact
www.austriamicrosystems.com
Revision 1.05
15 - 15

▲Up To Search▲

Price & Availability of AS1364-BTDT-12

	To Download AS1364-BTDT-12 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .